您好!欢迎来访东营博诚长臂挖掘机出租公司!关于我们 | 联系我们 | 在线留言
全国统一服务热线
18766733030
联系我们
联系人:王经理
联系电话:18766733030
地址:山东省东营市
新闻中心

对挖机加长臂你了解多少?

日期:2019-12-02   来源:
  在很多施工场地,我们经常看到很多和我们平时见到得不太一样的挖掘机,这种一般是为了特殊作业为设计或者改装的挖掘机。最常见的改装挖掘机是加长臂挖掘机,从市政建设、地铁交通的完善、下水道的改建、河道清理等都须要大量的工程机械设备,而标准的挖掘机械又完成不了特殊化的工程作业,所以此时加长臂挖掘机利用超长型动臂和超长型斗杆来大展神威,可在疏浚、护岸、坡面以及地铁建设等受地面环境限制的工况下,发挥巨大的威力。
加长臂挖掘机
  In many construction sites, we often see many excavators which are not the same as what we usually see. This kind of excavator is usually designed or modified for special operation. The most common refitted excavator is the long arm excavator, which requires a lot of engineering machinery and equipment from the municipal construction, the improvement of subway traffic, the reconstruction of sewers, river cleaning, etc., while the standard excavation machinery can not complete the special engineering work, so the long arm excavator uses the super long boom and the super long stick to show its power, which can be used in dredging, revetment and slope As well as the subway construction and other conditions limited by the ground environment, play a huge power.
  一般常见的有以下几个应用领域:
  The common application areas are as follows:
  1.两段式加长臂:使用范围相对较大,但是他的主要功能也只是为了提升挖掘半径,主要用于清理河道,填海造地,地铁出入口开挖,人行地底隧道,还有高速公路防护墙修整,一般住宅输送一下水泥等等。也有人用他前置破碎锤作用于房屋拆迁的,不过比较危险。两段式加长臂一般10-26米区间改装比较多。
  1. Two section long arm: it has a relatively large range of use, but its main function is only to improve the excavation radius, mainly used for cleaning up river channels, land reclamation, subway entrance and exit excavation, pedestrian underpass tunnel, as well as highway protective wall repair, general residential transportation of cement and so on. Some people use his front crushing hammer to remove houses, but it is dangerous. Generally, there are many refits in the 10-26m interval of the two-stage boom.
  2.三段式加长臂:或者多段式加长臂,主要应用于高层建筑的拆迁,前置破碎锤或者液压钳。20-28米内使用者比较多。
  2. Three section extension arm: or multi section extension arm, mainly used for demolition of high-rise buildings, pre crushing hammer or hydraulic tong. There are many users within 20-28 meters.
  3.滑臂或者内伸缩臂:主要为了回转半径很小,但是挖掘深度要求很高的工况设计,一般会前置贝壳挖斗(贝形斗)。滑臂垂直挖掘最大深度一般为10米,内伸缩臂垂直挖掘深度一般在26米以内。
  3. Sliding arm or inner extension arm: it is mainly designed for the working condition with small turning radius and high excavation depth requirements. Generally, the shell bucket (shell bucket) is placed in front of it. The maximum depth of vertical excavation of sliding arm is generally 10m, and the vertical excavation depth of internal telescopic arm is generally within 26m.
  4.打桩机加长臂:大小臂平直,前置弯臂2.6米左右(主要是为了与振动锤连接是便于阀块和管路的安装)及震动锤,应用于修建公路铁路或者埋设管道的时候打拔钢板桩。
  4. Extension arm of pile driver: the big and small arms are straight, the front bending arm is about 2.6m (mainly for connecting with the vibration hammer to facilitate the installation of valve block and pipeline) and the vibration hammer, which shall be used to drive and pull the steel sheet pile when constructing the highway railway or burying the pipeline.
  5.抓木机、抓料机装卸煤机加长臂:更多的时候为了装卸火车或者汽车而设计,一般大臂7.6米,小臂5-6米.前置抓木器、抓钳器或者贝壳挖斗。
  5. Long arm of coal handling machine of wood grabbing machine and material grabbing machine: more often, it is designed for loading and unloading trains or cars. Generally, the big arm is 7.6m, and the small arm is 5-6m. The front grabber, tongs or shell digging bucket.

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】